Lecteur de carte DAB qui ne lit pas ? Dip vs motorisé vs sans contact, bourrages, contacts puce et cartes retenues
Un guide opérateur pour un lecteur de carte de DAB qui ne lit pas ou retient les cartes — les types dip, motorisé et sans contact, nettoyer la tête et les contacts puce, dégager les bourrages d'obturateur, lire le code d'erreur, et gérer une carte capturée.
Le tri rapide
An ATM card reader that won’t read — or worse, swallows cards — rarely has a dead reader. The usual causes are a dirty magnetic head, fouled chip (ICC) contacts, or a mechanical jam. The fault code and the symptom tell you which, and most fixes are cleaning and clearing. Triage in this order:
| Do this | What it rules out | |
|---|---|---|
| 1. Clean the reader; test a known-good card | Dirty head + worn customer card — the top two causes | — |
| 2. Read the fault code | Separates a stripe fault from an ICC (chip) fault from a jam | — |
| 3. Clear any jam in the card path | A stuck card or debris stops reads | — |
| 4. Clean the chip (ICC) contacts | Stripe-reads-but-chip-fails is the ICC contacts | — |
| 5. Cross-test / escalate | Confirms reader vs card; flags tamper for security | — |
Lecteurs dip, motorisé et sans contact
Which reader type your ATM uses changes both the symptoms and the fix — especially whether it can physically retain a card:
| Dip | Motorized | Contactless | |
|---|---|---|---|
| How it reads | Insert & withdraw; card never stays in | Pulls card in, holds, then ejects | Tap (NFC); card never inserted |
| Can retain a card? | No | Yes | No |
| Magnetic head | Yes | Yes | No |
| Chip (ICC) contacts | Usually | Usually | No (uses NFC) |
| Typical faults | Dirty head, ICC contacts | Jams, capture, sensors | Antenna / NFC module |
Lire le symptôme
Match the symptom to point at the cause before you open anything:
| Symptom | Most likely cause | |
|---|---|---|
| No card reads at all | Dirty/failed magnetic head, or a reader/comms fault | — |
| Some cards read, others don't | Worn/demagnetized customer cards — not the reader | — |
| Stripe reads, chip fails | Dirty, worn or misaligned ICC contacts | — |
| Card jams / won't go in | Debris or foreign object in the card path | — |
| Retains cards (motorized) | Jam, timeout, capture flag, or a failing sensor | — |
| Contactless won't tap | NFC antenna/module fault or config | — |
Pas à pas : dégager les causes courantes
Work the sequence in order, within your machine’s documented procedure and security rules. Stop and escalate if the fault is beyond routine clearing.
- 1
Clean the head and test
Run a cleaning card through the reader to clear the magnetic head, then test with a known-good card. This resolves the most common read failures. - 2
Read the fault code
Check the operator menu — a magnetic-stripe error, an ICC (chip) error and a jam each point at a different fix. - 3
Clear any jam
Power down the reader per procedure, gently remove a stuck card or debris from the throat/transport without forcing it, and inspect the card path.Caution: If a foreign object looks intentionally placed, treat it as possible skimming — escalate, don't just remove it. - 4
Clean the chip contacts
If the stripe reads but the chip fails, clean the ICC contact area per your machine’s method and re-test a known-good chip card. - 5
Cross-test, then power-cycle or escalate
Confirm reader vs card with known-good cards, power-cycle, and re-test. If the code points at the head, controller or motor — or cards are still retained — call authorized service.
Gérer une carte retenue (capturée)
Card retention is unique to motorized readers and is a cash-/security-adjacent event, so it has its own handling rules beyond “fix the reader”:
| Situation | What to do | |
|---|---|---|
| Card retained at end of transaction | Reconcile to the capture bin; log it per procedure | — |
| Returning a captured card | Verify the cardholder per your operator's secure process — never hand back unverified | — |
| Frequent retention | Suspect a jam, dirty/failing sensor, or misfeed — service the reader | — |
| Capture bin full | Empty and reconcile per procedure; a full bin can halt the reader | — |
Pièces d'usure et quand appeler le service
When cleaning and clearing don’t fix it, these are the parts that wear or fail in an ATM card reader — fitted by authorized service, matched to your machine:
| Part | Symptom when failing | |
|---|---|---|
| Magnetic read head | Stripe won't read after cleaning (see heads guide) | — |
| ICC (chip) contact block | Chip fails while stripe reads | — |
| Shutter / gate | Card won't enter, or jams at the throat | — |
| Transport rollers / motor (motorized) | Misfeeds, retention, intermittent transport | — |
| Sensors | False jams/retention, mis-detected card position | — |
| Contactless (NFC) module | Taps not detected on a contactless reader | — |
Browse readers and related parts in our card readers & scanners and terminal repair parts categories. For the read-head deep-dive see our ATM card reader heads guide; for the POS hand-swipe MSR (a different device) see the POS card reader guide; and for other ATM peripherals, the cash dispenser and PIN pad (EPP) guides. Tell us your ATM and reader type and we’ll match the right part.
Questions fréquentes
Mon DAB ne lit pas les cartes — par où commencer ?
Quelle différence entre un lecteur dip, motorisé et sans contact ?
Le lecteur lit la bande mais pas la puce — pourquoi ?
Pourquoi mon DAB retient-il (avale) sans cesse les cartes des clients ?
Comment dégager un bourrage de carte dans le lecteur en sécurité ?
Quand arrêter et appeler un service agréé ?
Sources & lectures complémentaires
- Common ATM Error Codes and How to Fix Them — ATM Depot
- Troubleshooting Common ATM Errors: Repair vs Replace — Dollar ATM Club
- Nautilus Hyosung ATM Support (card reader) — Nautilus Hyosung
- Card Reader Technologies: Dip, Motorized, Contactless — ID TECH
- ATM & Kiosk Card Reader Maintenance — Kiosk Industry
Guides associés
Terminal POS hors ligne ou sans connexion ? Dépannage réseau du voyant de lien au processeur
Un POS « hors ligne » n'est pas toujours de votre faute — la rupture peut être le câble, le routeur, internet, ou le processeur de paiement. Voici comment trouver vite quel maillon de la chaîne a lâché.
Lire le guide →Imprimante de reçus DAB qui n'imprime pas ? Bourrages, chargement, capteurs et lecture du code d'erreur
Un DAB qui distribue des espèces mais n'imprime pas de reçu a rarement une imprimante morte — c'est généralement une fin de papier, un bourrage, du papier à l'envers, ou un capteur poussiéreux. Voici comment dégager les causes courantes.
Lire le guide →Bourrage du massicot automatique d'imprimante de reçus POS : dégager, réinitialiser et remplacer le module de coupe (Epson, Star, Bixolon)
Un massicot bloqué arrête la caisse, pas seulement l'imprimante. Voici la séquence exacte pour le débloquer en sécurité en moins de deux minutes — et comment savoir si la lame est usée plutôt que simplement coincée.
Lire le guide →Catégories associées
Pièces en vedette
%20Sparta%20Riser%20Card/120c399634d85265f7a7595a979407ee_c48b4b186f0a2eea2b86d0d5a86c219e_s-l1600.jpg)
Besoin des pièces mentionnées dans ce guide ?
Pièces OEM d'origine et alternatives testées en usine pour les systèmes IBM, Toshiba, NCR, Diebold, Wincor et Hyosung — avec expédition mondiale.
