¿Visor de cliente POS en negro o no funciona? Guía de alimentación, puerto COM, protocolo y reemplazo
Una guía de campo para un visor de cliente/poste POS (VFD o LCD) en negro o con caracteres ilegibles — cómo conecta por serie o USB-COM, una secuencia alimentación-cable-COM-protocolo, probar el puerto con un terminal, y elegir un reemplazo por emulación.
El triaje rápido
A blank customer (pole) display rarely means a dead screen. The display and its data link are separate, so the first thing to settle is whether it has power: a powered but idle display usually glows or shows a standby readout (some models literally display “rOFF” or “cOFF”). From there, almost every fault is a cable, a COM port, or a protocol mismatch — not the VFD. Triage in this order:
| Do this | What it rules out | |
|---|---|---|
| 1. Confirm power (own adapter) | No glow at all = power; pole displays are often powered separately | — |
| 2. Reseat the serial/USB data cable | A loose data link = powered but no sale data | — |
| 3. Match the COM port in the POS | Wrong COM number — the #1 config fault | — |
| 4. Match baud rate and emulation | Garbled text = wrong baud or command protocol | — |
| 5. Test the port, then replace | Proves the display vs the software before you buy | — |
Cómo conecta un visor de cliente
A customer display — usually a blue-green VFD (vacuum fluorescent display), sometimes an LCD — receives text from the POS over a serial link: a real RS-232 port, or a USB connection that presents itself as a virtual COM port. The POS sends characters and control commands; the display’s controller interprets them and shows the price or total.
Two facts follow from this. First, power and data are independent — the display can be lit yet show nothing because no data is arriving. Second, the controller only understands one command emulation (Epson ESC, UTC, EMAX, ADM and others), so the POS must send the matching protocol or you get blank or garbled output.
Leer el síntoma
The exact symptom narrows the cause quickly:
| Symptom | Most likely cause | |
|---|---|---|
| Totally dark, no glow | No power — adapter, cable or outlet | — |
| Glows / standby readout, no sale data | Data cable, wrong COM port, or POS not configured | — |
| Garbled / random characters | Wrong baud rate, or wrong command emulation | — |
| Shows some text, freezes | Loose cable or flaky USB-COM connection | — |
| Worked until a PC change | COM number reassigned — re-point the POS | — |
| Nothing even via PuTTY (correct settings) | Cable, port, or the display itself failed | — |
Paso a paso: alimentación, cable, COM, protocolo
Work the sequence in order and stop when the total shows correctly. Each step proves a link in the chain so you never replace a healthy display.
- 1
Confirm power
Check the display’s own power adapter at both ends and the outlet. Look for a glow or standby readout. No light at all is a power fault — fix that first. - 2
Reseat the data cable
Firmly reseat the serial or USB data cable at both the display and the terminal. Inspect for bent pins or damage. A half-seated data cable is a classic “powered but blank” cause. - 3
Match the COM port
In Device Manager, find the COM number the display uses, then set that exact COM port in your POS software. A wrong COM number is the single most common reason a healthy display stays blank. - 4
Match baud rate and emulation
Set the baud rate and serial parameters (often 9600, 8-N-1 — check the manual). If text is garbled, the command emulation is wrong — set the POS to the protocol your display speaks (Epson ESC, UTC, EMAX, ADM, etc.).Caution: Wrong baud rate produces garbage characters; wrong emulation produces blank or scrambled output. - 5
Test the port, then replace
Open the COM port in a terminal program (PuTTY) and type. Characters appear = hardware fine, fix the POS config. Nothing appears with correct settings = the cable, port or display has failed — replace the display.
Puerto COM, baudios y emulación de comandos
Most “dead display” tickets are really a settings mismatch. These are the four parameters that have to agree between the POS and the display:
| Setting | What to check | |
|---|---|---|
| COM port number | The exact virtual/real COM the display enumerates as (Device Manager) | — |
| Baud rate | Match the display's rated speed — 9600 is common; wrong = garbage | — |
| Data bits / parity / stop bits | Usually 8-N-1; must match the display's spec | — |
| Command emulation / protocol | Epson ESC, UTC, EMAX, ADM… set the POS to the display's set | — |
Elegir un visor de cliente de reemplazo
When a verified-good port and settings still produce nothing, the display or its controller has failed. Match the replacement on these specs for a clean swap:
| Spec | How to choose | |
|---|---|---|
| Interface | Serial RS-232 or USB — match your terminal's port | — |
| Command emulation | Pick one your POS supports (Epson ESC, UTC, EMAX, ADM…) | — |
| Display type | VFD (bright, wide viewing angle) or LCD | — |
| Character layout | Commonly 2 lines × 20 characters — match your POS output | — |
| Mount / pole | Pole height and base that fit your counter | — |
Browse customer and pole displays in our displays & monitors category, and serial/USB cables in cables & connectors. If the main operator screen is the one at fault rather than the customer display, see our touchscreen troubleshooting guide. Tell us your POS software and the emulation it supports, and we’ll match a compatible display before you order.
Preguntas frecuentes
Mi visor de cliente (poste) POS está completamente en negro — ¿por dónde empiezo?
El visor tiene corriente pero no muestra nada durante una venta — ¿está roto?
¿Cómo encuentro el puerto COM y baudios correctos?
¿Cómo pruebo si el visor en sí funciona?
El visor muestra caracteres ilegibles en vez del precio — ¿por qué?
¿Cuándo reemplazo el visor de cliente, y qué hago coincidir?
Fuentes y lecturas complementarias
- How to Set Up a Pole Display / Customer Display (VFD) — SambaPOS Knowledgebase
- Common Issues with a POS Pole Display and How to Resolve Them — Alexandria Point of Sale
- The Display on My VFD Is Blank — What Does This Mean? — Power Knowledge
- Configure a POS-X Pole / Customer Display — POSGuys
- Common Problems of POS Systems (Customer Display) — GS POS System
Guías relacionadas
Atascos del cortador automático en impresoras de recibos POS: cómo despejar, reiniciar y reemplazar el cortador (Epson, Star, Bixolon)
Un cortador atascado detiene la caja, no solo la impresora. Aquí está la secuencia exacta para despejarlo con seguridad en menos de dos minutos — y cómo saber si la cuchilla está gastada en vez de solo atascada.
Leer guía →¿El cajón portamonedas no abre? La guía completa de diagnóstico, cableado y voltaje (RJ11/RJ12)
Nueve de cada diez veces, un cajón muerto es un error de impresora, un cable suelto o un voltaje incorrecto — no un cajón roto. Aquí está la ruta de diagnóstico completa, el pinout exacto del puerto DK y cómo evitar quemar un solenoide.
Leer guía →Fallo de la fuente de alimentación POS y cajero: diagnóstico, prueba con multímetro y reemplazo según especificación
Un terminal POS que no enciende es un problema de fuente mucho más a menudo que de placa. Aquí está cómo confirmarlo con un multímetro y cómo elegir un reemplazo que no dañe el terminal.
Leer guía →Categorías relacionadas
Repuestos destacados
%20Sparta%20Riser%20Card/120c399634d85265f7a7595a979407ee_c48b4b186f0a2eea2b86d0d5a86c219e_s-l1600.jpg)
¿Necesita las piezas mencionadas en esta guía?
Piezas OEM originales y alternativas probadas en fábrica para sistemas IBM, Toshiba, NCR, Diebold, Wincor y Hyosung — con envío mundial.
