Afficheur client POS noir ou ne fonctionne pas ? Guide alimentation, port COM, protocole et remplacement
Un guide terrain pour un afficheur client/colonne POS (VFD ou LCD) noir ou brouillé — comment il se connecte en série ou USB-COM, une séquence alimentation-câble-COM-protocole, tester le port avec un terminal, et choisir un remplacement par émulation.
Le tri rapide
A blank customer (pole) display rarely means a dead screen. The display and its data link are separate, so the first thing to settle is whether it has power: a powered but idle display usually glows or shows a standby readout (some models literally display “rOFF” or “cOFF”). From there, almost every fault is a cable, a COM port, or a protocol mismatch — not the VFD. Triage in this order:
| Do this | What it rules out | |
|---|---|---|
| 1. Confirm power (own adapter) | No glow at all = power; pole displays are often powered separately | — |
| 2. Reseat the serial/USB data cable | A loose data link = powered but no sale data | — |
| 3. Match the COM port in the POS | Wrong COM number — the #1 config fault | — |
| 4. Match baud rate and emulation | Garbled text = wrong baud or command protocol | — |
| 5. Test the port, then replace | Proves the display vs the software before you buy | — |
Comment un afficheur client se connecte
A customer display — usually a blue-green VFD (vacuum fluorescent display), sometimes an LCD — receives text from the POS over a serial link: a real RS-232 port, or a USB connection that presents itself as a virtual COM port. The POS sends characters and control commands; the display’s controller interprets them and shows the price or total.
Two facts follow from this. First, power and data are independent — the display can be lit yet show nothing because no data is arriving. Second, the controller only understands one command emulation (Epson ESC, UTC, EMAX, ADM and others), so the POS must send the matching protocol or you get blank or garbled output.
Lire le symptôme
The exact symptom narrows the cause quickly:
| Symptom | Most likely cause | |
|---|---|---|
| Totally dark, no glow | No power — adapter, cable or outlet | — |
| Glows / standby readout, no sale data | Data cable, wrong COM port, or POS not configured | — |
| Garbled / random characters | Wrong baud rate, or wrong command emulation | — |
| Shows some text, freezes | Loose cable or flaky USB-COM connection | — |
| Worked until a PC change | COM number reassigned — re-point the POS | — |
| Nothing even via PuTTY (correct settings) | Cable, port, or the display itself failed | — |
Pas à pas : alimentation, câble, COM, protocole
Work the sequence in order and stop when the total shows correctly. Each step proves a link in the chain so you never replace a healthy display.
- 1
Confirm power
Check the display’s own power adapter at both ends and the outlet. Look for a glow or standby readout. No light at all is a power fault — fix that first. - 2
Reseat the data cable
Firmly reseat the serial or USB data cable at both the display and the terminal. Inspect for bent pins or damage. A half-seated data cable is a classic “powered but blank” cause. - 3
Match the COM port
In Device Manager, find the COM number the display uses, then set that exact COM port in your POS software. A wrong COM number is the single most common reason a healthy display stays blank. - 4
Match baud rate and emulation
Set the baud rate and serial parameters (often 9600, 8-N-1 — check the manual). If text is garbled, the command emulation is wrong — set the POS to the protocol your display speaks (Epson ESC, UTC, EMAX, ADM, etc.).Caution: Wrong baud rate produces garbage characters; wrong emulation produces blank or scrambled output. - 5
Test the port, then replace
Open the COM port in a terminal program (PuTTY) and type. Characters appear = hardware fine, fix the POS config. Nothing appears with correct settings = the cable, port or display has failed — replace the display.
Port COM, débit en bauds et émulation de commandes
Most “dead display” tickets are really a settings mismatch. These are the four parameters that have to agree between the POS and the display:
| Setting | What to check | |
|---|---|---|
| COM port number | The exact virtual/real COM the display enumerates as (Device Manager) | — |
| Baud rate | Match the display's rated speed — 9600 is common; wrong = garbage | — |
| Data bits / parity / stop bits | Usually 8-N-1; must match the display's spec | — |
| Command emulation / protocol | Epson ESC, UTC, EMAX, ADM… set the POS to the display's set | — |
Choisir un afficheur client de remplacement
When a verified-good port and settings still produce nothing, the display or its controller has failed. Match the replacement on these specs for a clean swap:
| Spec | How to choose | |
|---|---|---|
| Interface | Serial RS-232 or USB — match your terminal's port | — |
| Command emulation | Pick one your POS supports (Epson ESC, UTC, EMAX, ADM…) | — |
| Display type | VFD (bright, wide viewing angle) or LCD | — |
| Character layout | Commonly 2 lines × 20 characters — match your POS output | — |
| Mount / pole | Pole height and base that fit your counter | — |
Browse customer and pole displays in our displays & monitors category, and serial/USB cables in cables & connectors. If the main operator screen is the one at fault rather than the customer display, see our touchscreen troubleshooting guide. Tell us your POS software and the emulation it supports, and we’ll match a compatible display before you order.
Questions fréquentes
Mon afficheur client (colonne) POS est complètement noir — par où commencer ?
L'afficheur a du courant mais ne montre rien pendant une vente — est-il cassé ?
Comment trouver le bon port COM et débit en bauds ?
Comment tester si l'afficheur lui-même marche ?
L'afficheur montre des caractères brouillés au lieu du prix — pourquoi ?
Quand remplacer l'afficheur client, et quoi faire correspondre ?
Sources & lectures complémentaires
- How to Set Up a Pole Display / Customer Display (VFD) — SambaPOS Knowledgebase
- Common Issues with a POS Pole Display and How to Resolve Them — Alexandria Point of Sale
- The Display on My VFD Is Blank — What Does This Mean? — Power Knowledge
- Configure a POS-X Pole / Customer Display — POSGuys
- Common Problems of POS Systems (Customer Display) — GS POS System
Guides associés
Bourrage du massicot automatique d'imprimante de reçus POS : dégager, réinitialiser et remplacer le module de coupe (Epson, Star, Bixolon)
Un massicot bloqué arrête la caisse, pas seulement l'imprimante. Voici la séquence exacte pour le débloquer en sécurité en moins de deux minutes — et comment savoir si la lame est usée plutôt que simplement coincée.
Lire le guide →Tiroir-caisse qui ne s'ouvre pas ? Le guide complet de dépannage, câblage et tension (RJ11/RJ12)
Neuf fois sur dix, un tiroir-caisse mort est une erreur imprimante, un câble lâche ou une tension inadaptée — pas un tiroir cassé. Voici le parcours de diagnostic complet, le brochage exact du port DK, et comment éviter de griller un solénoïde.
Lire le guide →Panne d'alimentation POS & DAB : diagnostic, test au multimètre et remplacement aux bonnes spécifications
Un terminal POS qui ne s'allume pas est bien plus souvent un problème d'alimentation qu'un problème de carte. Voici comment le confirmer au multimètre et choisir un remplacement qui n'endommagera pas le terminal.
Lire le guide →Catégories associées
Pièces en vedette
%20Sparta%20Riser%20Card/120c399634d85265f7a7595a979407ee_c48b4b186f0a2eea2b86d0d5a86c219e_s-l1600.jpg)
Besoin des pièces mentionnées dans ce guide ?
Pièces OEM d'origine et alternatives testées en usine pour les systèmes IBM, Toshiba, NCR, Diebold, Wincor et Hyosung — avec expédition mondiale.
